![]() *This guide does not include instructions for establishing an SSH or Console connection in Putty or the Mac OS terminal app. You will also want to make sure you do not have any gaps in coverage between zones of your WiFi Network before you run these commands: there is no command line magic trick to fix the need for an additional AP to fill those gaps in coverage. To execute these commands, you will need the Putty application for Windows or the Terminal application built into Mac OS, as well as the skills and experience to open and connect via SSH. There are a few options for further optimizing your 5 GHz network in Ruckus Unleashed via the Command Line. The connectivity to the carrier is maintained just as it is in standard LTE networks by using the Ruckus Wi-Fi calling feature enabled on any WLAN deployed on a Ruckus Unleashed system. The Data flow can be seen in the two Network Diagrams below. These settings allow a client device to successfully roam from the Wi-Fi network, to a cellular LTE connection, during a WiFi Calling session, without any drops or interruptions. Ruckus provides the ability to identify a Voice Wi-Fi call through Ruckus QOS and establish a tunneled connection to the local carrier’s Packet Data Gateway. This is due to the lack of visibility of the carrier system to the client traffic before the device establishes a cellular LTE link. However, when that device leaves the WiFi Network and attempts to transition to the LTE Cellular Network, the call is dropped. In a normal Wi-Fi calling scenario, the client device connects to the local WLAN and a call is established, usually without any issues. Ruckus W-Fi calling creates an ecosystem for Voice that is not only best-in-class in service and reliability but is also on the leading edge of the Voice over Wi-Fi standard. They simply provide enhanced capabilities. The settings on this page do not make Wifi calling work or not work. These 3x WLANs will cover 95% of use cases but not 100%, this is not unique to Ruckus, this is true of any enterprise WiFi system.įollow the instructions first, update your client device software and firmware, delete and re-add the SSID in the client device, and if you are still having issues with a specific device not cooperating, call us. Note: If all client devices were the same, this would be easy! But they aren’t, so it’s not. We will use 5 GHz for this network with a narrow bandwidth (20 MHz, 40 MHz) because there are more 5 GHz channels available, avoiding co-channel interference with the rest of your network. You can even set a lease time, such as 12 hours, so that guests are removed from the network after a certain interval. They will only have access to the internet and wifi calling services. This will allow the owners of the network to allow guests on their network without access to the rest of the system. Also, because 2.4 GHz travels further through architecture, this will guarantee that your critical Control System and IoT devices get connected to the network, and stay connected to the network. This will separate control systems, IoT, low bandwidth, and even legacy devices (ie 802.11b) from the high speed 5 GHz Homeowner network. By setting this WLAN to 5 GHz only, this will guarantee that devices on this SSID will have a clean, clear radio channel with a lot of available airtime for WiFi calling and low interference for high speeds. When you went through the Quick Start guide, this should be the SSID you created first (will not be 5 GHz only by default, we will make that change later). This should be your first and primary WiFi network. If you are replacing an older network, you will achieve the best results by deleting and re-adding the old SSID and password from your client devices, even if the SSID and password are exactly the sameīlackwire recommends 3 standard WLANs, and we will show you how to set these WLANs up, step by step: Joining client devices to a partially configured network can result in certain client devices blacklisting your network and refusing to join! *Note: It is highly recommended to complete this entire Best Practices setup, in this exact order, on a single AP, before adding additional APs, and before joining client devices. Attempting to use wifi can result in system errors and corrupt firmware images. As you configure the Unleashed System, there will be several interruptions to the WiFi Network. Important: Turn off the wifi on your computer and plug directly into the network switch with an ethernet cable for the duration of this setup. Please be sure to check the Blackwire Ruckus 101 main page regularly for the best-recommended firmware version. Important: Blackwire currently recommends Unleashed firmware version 200.13.6.1.319 as the most stable current firmware.
0 Comments
Leave a Reply. |